AXX35 www.axtal.com wasemweg 5 page 1(2) fon: +49 (6261) 939834 d-74821 mosbach fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg specification AXX35 issue: 01 date: 2003-11-08 oscillator type : quartz crystal unit in hc-35/u package parameter min. typ. max. unit condition frequency range 5 200 mhz actual frequency f 0 mhz crystal cut at mode 1 3 5 7 9 5 ~ 30 25 ~ 90 60 ~ 150 110 ~ 200 150 ~ 200 mhz mhz mhz mhz mhz load capacitance c l 10 ~ 50 pf or series adjustment tolerance -10 +10 ppm @ 25c +-3c frequency stability ppm overall (note 1) frequency stability over temperature range 5 ~ 50 ppm operating temperature range (st eady state) -55 +105 c available combinations on request long term (aging) 2 ppm over 10 years g-sensitivity ppb/g resonance resistance r r ? see table 1 motional capacitance c 1 ff static capacitance c 0 7 pf drive level 100 w insulation resistance 500 m ? 100 v dc storage temperature range -55 +105 c enclosure (see drawing) hc-35/u iec 60122-3 type ck can height h 6.5 mm marking frequency (mhz AXX35 wwaxyy packing bulk iec 60286-3 notes: 1. overall frequency stability = initial tolerance + temp. stability + aging (1 st year) 2. terminology and test conditions are according to iec standard iec60122-1, unless otherwise stated 3. measurement technique according to iec 60444-5 or equivalent table 1: resistance r 1 frequency [mhz] overtone r 1max [ ? ] 5 ~ 9.999 1 80 10 ~ 14.999 1 50 15 ~ 19.999 1 40 20 ~ 35 1 30 25 ~ 49.999 3 rd 100 50 ~ 100 3 rd 90 60 ~ 79.999 5 th 150 80 ~ 160 5 th 100 110 ~ 200 7 th 150 150 ~ 200 9 th 200
AXX35 www.axtal.com wasemweg 5 page 2(2) fon: +49 (6261) 939834 d-74821 mosbach fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg enclosure drawing note: tag position optional environmental conditions test iec 60068 part ... iec 61178-1 clause ... test conditions visual inspection, dimensions 4.5 4.6 enclosure styles as in iec 60122-3, if applicable sealing tests 2-17 4.8.2 gross leak: test qc, fine leak: test qk solderability resistance to soldering heat 2-20 4.8.3 test ta (235 5)c method 1 test tb method 1a, 5s shock 2-27 4.8.8 test ea, 3 x per axes 100g, 6 ms half-sine pulse bump 2-29 4.8.6 test eb, 4000 bumps per axes, 40g, 6 ms free fall 2-32 4.8.9 test ed procedure 1, 2 drops from 1m height vibration, sinusoidal 2-6 4.8.7 test fc, 30 min per axes, 10 hz - 55 hz 0,75mm; 55 hz - 1 khz, 10g rapid change of temperature 2-14 4.8.5 test na, 10 cy cles at extremes of operating temperature range dry heat 2-2 4.8.11 test ba, 16 h at upper temperature indicated by climatic category damp heat, cyclic 2-30 4.8.12 test db variant 1 severity b), 55c/95% r.h., 6 cycles cold 2-1 4.8.13 test aa, 2 h at lower temperature indicated by climatic category climatic sequence 1-7 4.8.14 se quence of 4.8.11, 4.8.12 (1 st cycle), 4.8.13, 4.8.12 (5 cycles) damp heat, steady state 2-3 4.8.15 test ca, 56 days endurance tests - ageing - extended aging 4.9.1 4.9.2 30 days @ 85c 1000h, 2000h, 8000h @85c
|
